XYZmaker tutorial – Airplane part 3

XYZmaker_biplane_tutorial_img063 XYZmaker_biplane_tutorial_img064 To create an airfoil, first make a sphere, then in the Properties window change its dimensions to X: 40,Y: 40,Z: 4 mm and position to X: 0,Y: -36,Z: 55.   XYZmaker_biplane_tutorial_img065 XYZmaker_biplane_tutorial_img066 XYZmaker_biplane_tutorial_img067 Create a Cylinder and rotate it 90° along the Y axis, in the Properties window change the dimensions to X: 90,Y: 40,Z: 4 mm and position to X: 0,Y: -36,Z: 55   XYZmaker_biplane_tutorial_img068 XYZmaker_biplane_tutorial_img069 Select the Sphere you just created and click on the Clone button, change this new part’s X axis position to -45.   XYZmaker_biplane_tutorial_img070 XYZmaker_biplane_tutorial_img071 Drag select all parts and click on the Group button, to finish the upper wing part.   XYZmaker_biplane_tutorial_img072 Select the plane body you just moved to the side and to return it to the center, change its X axis position to 0 .   XYZmaker_biplane_tutorial_img073 Select the upper wing and click the Clone button.   XYZmaker_biplane_tutorial_img074 In the Properties window adjust the new part’s position to X: 0,Y: -20,Z: 8. This completes the lower wing.   XYZmaker_biplane_tutorial_img075 XYZmaker_biplane_tutorial_img076 Create a Hexagonal Prism and in the Properties window, change its dimensions to X: 40,Y: 36,Z: 20 mm and position to X: 0,Y: -12,Z: 55. Call this the cutting part.   XYZmaker_biplane_tutorial_img077 XYZmaker_biplane_tutorial_img078 XYZmaker_biplane_tutorial_img079 Select the upper wing and click on the Hole button, then select the cutting part and click the on the Hole button again.   XYZmaker_biplane_tutorial_img080 XYZmaker_biplane_tutorial_img081 Next start to make the wing supports, create a cylinder and in the Properties window, change its dimensions to X: 2,Y: 5,Z: 80 mm and position to X: 50,Y: -14,Z: 30. Call this part support.   XYZmaker_biplane_tutorial_img082 XYZmaker_biplane_tutorial_img083 Select support and rotate it 20° along the X axis.   XYZmaker_biplane_tutorial_img084 XYZmaker_biplane_tutorial_img085 Click the Clone button, and duplicate another support, change this duplicate support’s Y axis position to -40   XYZmaker_biplane_tutorial_img086 XYZmaker_biplane_tutorial_img087 Select either support and click on the Clone button again to create a third support. Next, change that part’s Y axis position to -27°. Now you should have 3 supports equally spaced out across the wing.   XYZmaker_biplane_tutorial_img088 XYZmaker_biplane_tutorial_img089 Select the support in the middle and rotate it 30° degrees along the X axis.   XYZmaker_biplane_tutorial_img090 XYZmaker_biplane_tutorial_img091 After all the supports are together, the ends that are overhanging the upper and lower wings need to be slowly cut away. Create a Cube and in the Properties window change the dimensions to X: 20,Y: 50,Z: 20 mm and position to X: 50,Y: -20,Z: -2. Call this part the cutting part.   XYZmaker_biplane_tutorial_img092 XYZmaker_biplane_tutorial_img093 Select the cutting part and click on the Clone button, in the Properties window change the new part’s position to X: 50,Y: -35,Z: 65.   XYZmaker_biplane_tutorial_img094 Select the left support and hold down the Ctrl key while you select the right support, click on Group to group these parts together. Parts in the same group can all be cut at the same time.   XYZmaker_biplane_tutorial_img095 XYZmaker_biplane_tutorial_img096 Click the two supports that are grouped together and click on the hole button. Next, select the cutting part above and click the hole button again to cut away the part of the support that is overhanging.   XYZmaker_biplane_tutorial_img097 XYZmaker_biplane_tutorial_img098 XYZmaker_biplane_tutorial_img099 Use the same method to trim the overhanging parts below before continuing.  

Leave a Reply

Your email address will not be published. Required fields are marked *